Sharp JX-9400 Technické informace Strana 151
- Strana / 211
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Table 6.12 IAQ strategies for rotating heat exchangers
Design Operation
Select a wheel equipped with purging
sector and install it with the purging
sector on the warm side of the wheel
Supply and exhaust fans should be located
and sized so that a positive pressure
difference of about 200 Pa is achieved
between supply and exhaust ducts at the
wheel level
Avoid hygroscopic wheels when
contamination is an important concern
Change wheels if they are warped
Install filters in both channels upwind of
the heat exchanger
If pressure on supply side is negative
compared to exhaust side then change
pressure hierarchy
If the rotation of wheel is in the wrong
direction then change to proper direction:
the wheel should pass from exhaust to
supply ducts in front of the purging sector
Clean dirty wheels according to
instructions of the manufacturer, with
either compressed air, vacuu m cleaner or
pressurized water
Check that the wheel control stops the
wheel when no heat can be recovered
Table 6.13 IAQ strategies for humidifiers
Design Operation
Prevent pollution from water, water tanks and devices/agents to disin fect, demineralize
and/or desalinate the water
Remove oil residue before use of
humidifier to prevent an oil film on water
Take care using disinfecting material
Use UV as germicide
De-ionization cartridges to prepare soft
water might emit VOCs
Install demineralization device in disperser
to keep the oscillator circuit board free
from mineral precipitation for as long as
possible
If there is an oil film on water surface,
drain water and clean humidifier
immediately
Change water every week
Clean tank (not possible for steam: keep
them dry/empty when not in use)
Clean humidifier regularly every six
months (dry or wet)
Desalinization must take place with an
agent that does not smell
Use a control system with which
Humidifier should automatically shut
down when the HVAC system is off
New water is added when the water
temperature exceeds 208C (spray nozzle
and evaporative humidifiers, ultrasonic
humidifiers)
Check operation of control system
regularly
Other recommendations
Do not use porous wet material
Prevent condensation from steam
humidifier
130 Ventilation and Airflow in Buildings
- Claude-Alain Roulet 4
- Contents 6
- List of Figures and Tables 8
- List of Figures and Tables ix 10
- List of Figures and Tables xi 12
- Preamble 13
- Introduction 14
- Outdoor airflow rate 15
- Recirculation rates 16
- Exfiltration 17
- Ventilation efficiency 18
- Airtightness 20
- Energy efficiency 20
- Common techniques 21
- Airflow Rates in Buildings 22
- Tracer decay, no injection 24
- Constant injection rate 24
- Constant concentration 25
- Pulse injection 25
- Airflow Rates in Buildings 5 26
- Airflow Rates in Buildings 7 28
- Global system of equations 29
- Airflow Rates in Buildings 9 30
- Properties of the flow matrix 31
- Airflow Rates in Buildings 11 32
- Note: y Under condition 34
- Source: Sherman, 1990 34
- Airflow Rates in Buildings 13 34
- Airflow Rates 36
- Source: Roulet et al., 2000a 37
- Velocity traverse 38
- Test procedure 39
- Tracer gas dilution 39
- Source: Awbi, 2007 40
- Inflatable bag 41
- Flowmeter 41
- Compensated flowmeter 41
- Tracer gas injection ports 41
- Source: Roulet et al., 1999 42
- Node by node method 44
- Least square solution 48
- Eliminating some equations 48
- Simplest way 49
- Less than four tracer gases 53
- Planning tool 54
- Simple measurement using CO 55
- Age of Air and 60
- Ventilation Efficiency 60
- Nominal time constant 61
- Air exchange efficiency 61
- Source: Roulet, 2004 62
- Measurement method 63
- Concentration [ppm] 65
- Source: Roulet et al., 1998 69
- The model matrix M 73
- Condition of the model matrix 74
- Factorial designs 75
- 3-D designs 76
- Measurement methods 80
- Reductive sealing 82
- Density corrections 84
- Two measurement points 85
- Airtightness 65 86
- Airtightness of buildings 88
- External fan 89
- Internal fan 90
- Leakage visualization 90
- The stack effect method 91
- Airtightness 71 92
- Neutral height method 93
- Airtightness 73 94
- Pressurization method 95
- Flow rate difference method 96
- Conditioned space 97
- SealSeal 97
- Measurements and Measures 98
- Related to Energy Efficiency 98
- Energy in air handling units 100
- Heat exchangers 104
- Types of heat exchangers 105
- Rotating heat exchangers 106
- Glycol heat exchanger 107
- Heat pump 107
- Heat exchange efficiency 107
- Ventilated 110
- Global heat recovery efficiency 111
- Source: Roulet et al., 2001 114
- Examples of application 115
- Energy for ventilation 118
- Measurement of airflow rate 120
- Measurement of electric power 121
- Simulation results 126
- Recirculation 126
- Humidification 127
- Heat recovery 127
- Ductwork 128
- Contaminants in 129
- Air Handling Units 129
- Source: Bjo 130
- Humidifiers 131
- Source: Roulet et al., 2000 133
- Measurement protocols 134
- Selecting the panel 135
- Source: Bluyssen, 1990 136
- Training procedure 137
- Experimental day 138
- Principle of the method 138
- Injection technique 139
- Hot air blower (200 °C) 140
- Stainless steel 140
- Ø 6 mm copper tube 140
- Example of application 141
- Evidence for adsorption 144
- HVAC systems 146
- Common Methods 153
- Properties of tracer gases 155
- Source: Dietz et al., 1983 157
- Mixing tracer gases 158
- Tracer density problem 159
- Sampling methods 160
- Grab sampling 160
- Passive sampling 160
- Networks, pumps and pipes 161
- Tracer gas analysers 163
- Objective of the analysis 163
- Photo-acoustic detector 165
- Mass spectrometry 165
- Gas chromatography 167
- Chemical indicator tubes 167
- Identification methods 168
- Confidence in the coefficients 170
- Regression of the second kind 171
- Orthogonal regression 171
- Bayesian identification 172
- Error analysis 174
- Definitions 175
- A few statistics 175
- Covariance 177
- Statistical distributions 177
- What is the problem? 180
- Most simple error analysis 180
- Estimate of the variance 181
- Linear equations systems 181
- Upper bound of the errors 183
- References 187
- Unit Conversion Tables 192
- Pressure 194
- Volume flow rate 194
- Mass flow rate 194
- Glossary 195
- Glossary 175 196
- Glossary 177 198
- Glossary 179 200
- Glossary 181 202
- Glossary 183 204
- Glossary 185 206
Související produkty a manuály pro Tisk a skenování Sharp JX-9400
Tisk a skenování Sharp SF-1020 Servisní příručka
(140 stránky)
(140 stránky)
Tisk a skenování Sharp M450 U Uživatelský manuál
(2 stránky)
(2 stránky)
Tisk a skenování Sharp ER-01PU Specifikace
(86 stránky)
(86 stránky)
Tisk a skenování Sharp AR-M355U Servisní příručka
(33 stránky)
(33 stránky)
(641 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce