Sharp AR-168N Specifikace Strana 81
- Strana / 177
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
AR-168N/168L TEST COMMAND, TROUBLE CODES 10 - 6
6 01 Paper feed solenoid
(CPFS1, CPFS2, MPFS)
operation check (PSOL
CHK)
[Function]
When [ENTER/START] key is pressed, the selected paper feed solenoid repeats ON for 500ms and
OF for 500ms 20times.
When [
←
/
→
/10KEY] is pressed, the paper feed solenoid setting is switched.
[Operation]
02 Resist roller solenoid (RRS)
operation check (RES.R
SOL CHK)
[Function]
When [ENTER/START] key is pressed, the resist solenoid repeats ON for 500ms and OFF for 500ms
20 times.
[Operation]
7 01 Check of warm-up display
and aging with JAM (W-UP/
AGING)
[Function]
Copying is repeated to make the set quantity of copies.
When the test command is executed, warm-up is started and warm-up time is added for every second
from 0 and displayed.
When warm-up is completed, addition is stopped. When [CA] key is pressed, the ready lamp lights up.
After that, enter the copy quantity with [10KEY] and press [ENTER/START] key to repeat copying of
the set quantity (interval 0sec).
To cancel the test command, turn off the power or execute a test command which causes hardware
reset.
[Operation]
06 Interval aging (INTERVAL
AGING)
[Function]
Copying is repeated to make the set quantity of copies.
When the test command is executed, warm-up is performed and the ready lamp is lighted.
Enter the copy quantity with the [10KEY] and press [ENTER/START] key, and copying is executed to
make the set quantity of copies, and the ready state is kept for 3sec, and copying is executed again to
make the set quantity of copies. These operations are repeated.
To cancel the test command, turn off the power or execute a test command which executes hardware
reset.
[Operation]
08 Shift to copy with warm-up
display (W-UP C-MODE)
[Function]
Enter the test command code, and warm-up is started and warm-up time is counted for every second
from 0 and displayed.
When [CA] key is pressed during counting up, "0" is displayed on the display and counting is stopped.
However, warm-up is continued.
After completion of warm-up, counting is terminated. (The aging function is removed from test com-
mand 7-01.)
[Operation]
Main
code
Sub
code
Contents Details of function/operation
Code number Setting Remark
0 CPFS1
1 CPFS2 Operation is possible only when No. 2 cassette is installed.
2MPFS
1) Initial display
2) [
→
/10KEY]
2) [
←
/10KEY]
3) [ENTER/START]
4) Returns to the initial display.
06-01 PSOL CHK
0:CPFS1
06-01 PSOL CHK
1:CPFS2
06-01 PSOL CHK
2:MPFS
06-01 PSOL CHK
EXECUTING...
1) Initial display
06-02 RES.R SOL CHK
EXECUTING...
1) Initial display 2) After 10sec
07-01 W-UP/AGING
0
07-01 W-UP/AGING
10
1) Initial display (Basic display of copy)
READY TO COPY
100% A4 0
1) Initial display 2) After 10sec
07-08 W-UP C-MODE
0
07-08 W-UP C-MODE
10
10_TESTCOMMAND.fm 6 ページ ２００５年１１月１８日 金曜日 午後５時３７分
- DIGITAL MULTIFUNCTIONAL 1
- CAUTION 2
- CONTENTS 4
- [1] GENERAL 6
- [2] SPECIFICATIONS 7
- 3. Copy performance 8
- 4. SPLC printer 9
- 5. Scan function 9
- [3] CONSUMABLE PARTS 10
- 4. TD cartridge replacement 11
- 1. Appearance 12
- 2. Internal 12
- 18 19 20 21 13
- 4. Motors and solenoids 14
- 5. Sensors and switches 15
- 6. PWB unit 16
- 7. Cross sectional view 17
- 1. Copier installation 18
- 2. Cautions on handling 18
- Lock Unlock 19
- Grasp here and turn in 19
- CAUTION tape 19
- Protective pins 19
- Pressure plate lock 21
- [Custom installation] 23
- (1) Windows XP (USB/Parallel) 23
- (2) Windows 98/Me/2000 (USB) 24
- C. Setting up button manager 27
- (1) Windows XP 27
- (2) Windows 98/Me/2000 27
- (1) Connecting a USB cable 28
- 11. Interface 29
- 12. Moving 29
- [6] COPY PROCESS 30
- 2. Outline of print process 31
- 3. Actual print process 31
- About DC 5.2kV 32
- Process controlling 33
- [7] OPERATIONAL DESCRIPTIONS 34
- 34 6 285 35
- 3. Laser unit 36
- 4. Fuser section 36
- (1) Heat roller 37
- (2) Separator pawl 37
- (3) Thermal control 37
- (4) Fusing resistor 37
- A. Initial state 41
- B. Front copy 41
- C. Back copy 41
- 8. Shifter 42
- [8] DISASSEMBLY AND ASSEMBLY 43
- Example of NG 44
- Charger wire 46
- Protrusion 46
- 3. Optical section 47
- CCD core 48
- 4. Fusing section 49
- Heat roller disassembly 50
- Heater lamp 50
- C. Assembly procedure 56
- Back Wire treatment 57
- 7. Rear frame section 59
- 8. Power section 60
- 9. Duplex motor section 60
- (1) Remove the rear cabinet 61
- (2) Remove the RSPF 61
- F. Sensor PWB 62
- G. Pickup solenoid 62
- H. Clutch 62
- (1) Remove the clutch unit 62
- (2) Remove the clutch 63
- (1) Remove the pickup unit 63
- (1) Remove the parts 65
- (2) Remove the parts 66
- T. Solenoid 67
- (1) Remove the reverse gate 67
- (2) Remove the solenoid 67
- [9] ADJUSTMENTS 68
- B. Image position adjustment 69
- (1) Lead edge adjustment 69
- B4 or 8 1/2″ × 14″ paper 70
- A4 size rear edge 70
- Scale image 70
- Paper rear edge 70
- White paper 71
- Test chart 71
- 3. High voltage adjustment 72
- 4. Duplex adjustment 72
- Document guide 73
- The trailing edge has a scale 73
- Table glass 73
- Scale (D-D mode) 73
- 6cm or more is required 74
- 2. Key rule 76
- 3. List of test commands 76
- Image loss, R = 4mm 101
- Chart back surface 105
- 5. Trouble codes 114
- [11] MAINTENANCE 117
- [12] USER PROGRAM 118
- B. Print mode 119
- [13] ELECTRICAL SECTION 121
- 2. Circuit descriptions 122
- (4) Reset circuit 127
- ASIC/CPU 128
- Tonner Motor Driver 129
- TD62064AF 130
- (10) OPE PWB 131
- (11) Carriage Unit 131
- (1) Noise filter circuit 131
- Voltage waveform 132
- [14]CIRCUIT DIAGRAM 134
- Serial EE-PROM 135
- MCU PWB (ASIC section) 136
- MCU PWB (Memory section) 138
- MCU PWB (Driver section 1) 140
- MCU PWB (Driver section 2) 142
- MCU PWB (Driver section 3) 144
- MCU PWB (IMC2 section 1/2) 148
- MCU PWB (Connector section 1) 152
- To Operational PWB 153
- To Mirror motor 153
- MCU PWB (Connector section 3) 154
- To 2nd. cassette 155
- MCU PWB (Modem I/F Connector) 157
- MCU PWB (Scanner I/F section) 158
- 2. OPERATION PWB 159
- To MCU PWB 161
- To Drum Initial Detector 161
- To FAX Key PWB 161
- POWER SUPPLY (120V/127V) 162
- (1) MCU SECTION (1/3) 164
- [15] FIRMWARE DOWNLOAD 167
- PROCEDURES 167
- 5. Installing procedures 171
- LEAD-FREE SOLDER 175
- CAUTION FOR BATTERY DISPOSAL 176
- COPYRIGHT 177
- 2005 BY SHARP CORPORATION 177
Související produkty a manuály pro Multifunkční zařízení Sharp AR-168N
Multifunkční zařízení Sharp AR-156 Specifikace
(52 stránky)
(52 stránky)
Multifunkční zařízení Sharp AR-651 Servisní příručka
(42 stránky)
(42 stránky)
(2 stránky)
(12 stránky)
Multifunkční zařízení Sharp AL-1043 Servisní příručka
(216 stránky)
(216 stránky)
Multifunkční zařízení Sharp JW-20FLT Uživatelský manuál
(224 stránky)
(224 stránky)
(12 stránky)
Multifunkční zařízení Sharp AR-151 Specifikace
(52 stránky)
(52 stránky)
Multifunkční zařízení Sharp AR-810 Uživatelský manuál
(101 stránky)
(101 stránky)
(2 stránky)Grizzly G8183 manuales
Manuales del propietario y guías del usuario para Herramientas Grizzly G8183.
Ofrecemos 1 manuales en pdf Grizzly G8183 para descargar gratis por tipos de documentos: Manual de usuario
Tabla de contenidos
Más productos y manuales para Herramientas Grizzly
| Modelos | Tipo de documento |
|---|---|
| G1852 |
Manual de usuario
Grizzly G1852 User Manual,
27 paginas
|
| G8143 |
Manual de usuario
Grizzly G8143 User Manual,
16 paginas
|
| G1067Z |
Manual de usuario
Grizzly G1067Z User Manual,
28 paginas
|
| H8230 |
Manual de usuario
Grizzly H8230 User Manual,
20 paginas
|
| Paint Tank H8225 |
Manual de usuario
Grizzly Paint Tank H8225 User Manual,
2 paginas
|
| H8232 |
Manual de usuario
Grizzly H8232 User Manual,
5 paginas
|
| G6048 |
Manual de usuario
Grizzly G6048 User Manual,
17 paginas
|
| Power Feeder G4176 |
Manual de usuario
Grizzly Power Feeder G4176 User Manual,
3 paginas
|
| G8598 |
Manual de usuario
Grizzly G8598 User Manual,
17 paginas
|
| Power Feeder G7873 |
Manual de usuario
Grizzly Power Feeder G7873 User Manual,
32 paginas
|
| H8203 |
Manual de usuario
Grizzly H8203 User Manual,
2 paginas
|
| H7666 |
Manual de usuario
Grizzly H7666 User Manual,
24 paginas
|
| 4" |
Manual de usuario
Grizzly 4" User Manual,
24 paginas
|
| STILE AND RAIL SETS C1393-96 |
Manual de usuario
Grizzly STILE AND RAIL SETS C1393-96 User Manual,
2 paginas
|
| G0453PX |
Manual de usuario
Grizzly G0453PX User Manual,
72 paginas
|
| H7951 |
Manual de usuario
Grizzly H7951 User Manual,
28 paginas
|
| G7946 |
Manual de usuario
Grizzly G7946 User Manual,
28 paginas
|
| H6238 |
Manual de usuario
Grizzly H6238 User Manual,
3 paginas
|
| Wood Copy Attachment G2891 |
Manual de usuario
Grizzly Wood Copy Attachment G2891 User Manual,
28 paginas
|
| G7298 |
Manual de usuario
Grizzly G7298 User Manual,
28 paginas
|
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce