Sharp IQ-8000 Instalační manuál Strana 11
- Strana / 125
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
and RX LEDs glow red to show activity on the data wires. The TX
LED indicates the fiber modem is transmitting and the RX LED
indicates reception of data.
....................................................................................................................
lxiv
..........................................................................................................................7.10.2 Installation lxv
To install the MX-485-2, it is necessary to mount the unit to a rigid
service using #8 hardware in four places. Care should be taken
when selecting a mounting location to avoid sharp bends in the
connecting cables. Please note minimum bend radii of all fibers
being used, to avoid fracturing the fiber optic core.
....................................................................................................................
lxv
........................................................................................................7.10.3 Optical Transmission lxvii
The 485-2 series has been designed to be a reliable link for the
transmission of data over long distances. The loss budget of 15 dB
on 16.2u fiber should allow up to 5 kilometers of transmission
distance.
....................................................................................................................
lxvii
The power output specifications are measured with a logic low state
on the bus. When the bus is in the high impedance state, the
transmission LED is at a very low output level (<-36dBm). Logic
levels are encoded using pulse width modulation. If the optical
connection is lost, the output bus goes to the HiZ state.
....................................................................................................................
lxvii
..........8.0 Status Lights and Dealing with Communication Errors lxviii
..............................................................................................................8.1 Status Lights lxviii
.................................................................................................8.2 Communication Errors lxix
...........................................................................................8.2.1 LED Fatal Error Display Codes lxix
..........................................................................................................................8.2.2 Error Codes lxx
.........................8.3 Control Counters and Sense Input Numbers for Output Control PCB lxxi
..........................................................................8.4 Proper Setting of SAM 1 and SAM 2 lxxiii
..........................................................................8.5 IQ Systems Upgrades and Capacities 74
.......................................................................................8.6 RS-232/485 Terminal Servers 75
.8.6.1 IQ Server Controller to LANtronix UDS-1100 Terminal Server Wiring Diagram for RS-232 75
.8.6.2 IQ Server Controller to LANtronix UDS-1100 Terminal Server Wiring Diagram for RS-485 75
......................................................8.6.3 IQ Server Controller to the EasySync USB Converter lxxvi
......................................8.7 RS-232-485/422 Converters: Printed Circuit Board Layout lxxvii
..........................................................................................8.8 User Selectable Options lxxviii
..........................................................................................................8.9 Point Definitions lxxx
.......................................................................................................................8.9.1 Sense Inputs lxxx
Page xi of 110 IQ-400 Installation Manual 33-10057-001-C
- Installation Manual 1
- 33-10057-001 1
- 0.1 Board Diagrams 3
- 0.1.4 OUT Expansion Board 6
- 0.1.5 ALM Expansion Board 7
- 0.1.6 SAM Board 8
- 0.2 Table of Contents 9
- 1.0 Introduction 14
- 2.0 Unpacking the IQ-400 16
- IQ-400 - Expansion Cable Plug 19
- 3.0 Installing Power 20
- 4.0 Wiring Your Readers 24
- 4.3.1 Procedure 25
- 4.4.1 Procedure 28
- 4.4.2.1 Procedure 28
- 5.0 Reader Connections 29
- Option 1 34
- Option 2 35
- – Option 2 37
- IQ-400 Board 38
- Expansion Board 39
- 6.0 Wiring the Door(s) 46
- 6.6.3 SAM Board LED Arrays 56
- Exit Sense Inputs 59
- 6.10.1 Procedure 61
- 7.1 Reset the IQ-400 Panel 62
- 7.5 Changing the Baud Rate 69
- PCSC P/N: 04-10318-101 73
- PCSC P/N: 04-10318-001 73
- HyperTerminal 76
- Protocol) 77
- 7.10.2 Installation 78
- 7.10.3 Optical Transmission 80
- 8.1 Status Lights 81
- 8.2 Communication Errors 82
- 8.2.2 Error Codes 83
- (Pins 2-3) 86
- 8.8 User Selectable Options 91
- 8.9 Point Definitions 93
- 8.9.1 Sense Inputs 93
- S3 through S6 are 94
- IQ 4 PCB 94
- 8.9.2 Outputs 96
- Connector 96
- 9.1 IQ-400 Features 99
- 9.1.3 Spare Parts- IQ-400 PCB 100
- 9.2.1 Electrical Ratings 101
- 9.2.2 Power Supply 101
- 9.2.3 Door Sense LEDs 102
- 9.2.5 Jumpers 102
- 9.3.2 System Capacities 104
- 9.3.3 Electrical Ratings 104
- 9.4.1 Electrical Ratings 106
- 9.4.2 Power Supply 106
- 9.4.3 Door Sense LEDs 107
- 9.4.5 Jumpers 107
- 9.5.1 System Capacities 109
- 9.5.2 Electrical Ratings 109
- 9.6.1 System Capacities 111
- 9.6.2 Electrical Ratings 111
- 9.6.3 Spare Parts- OUT PCB 111
- 9.7.1 System Capacities 112
- 9.7.2 Electrical Ratings 112
- 9.8 SAM Board 113
- 4-wire PCSC 114
- 5-wire Wiegand 114
- 9.10 Tool Requirements 115
- 10.1.1 Required Equipment: 118
- 10.1.2 Required Information: 118
- 10.1.3 Required firmware: 118
- 10.3.1 TCP/IP Configuration 121
- 10.4 Resetting the IQ-400E 124
- End of Manual 125
- PCSC, Inc 125
- August 2008 125
Související produkty a manuály pro Součásti zabezpečovacího zařízení Sharp IQ-8000
(14 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.251 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce