Sharp AR-350 Specifikace

LASER PRINTEROperation Manual (for copier)Be sure to become thoroughly familiar with this manual to gain the maximum benefit from the product.Before i

8 Standard original setting orientationDescriptions of functions that follow in this manual assume that originals are oriented as shown.Document

9NORMAL COPYINGThis section describes the normal copying procedure.Copying from the automatic document feeder 1-sided copies of 1-sided originals

10When originals are placed in the document feeder tray, asort icon will appear on the touch panel and the sortcopy mode will be automatically selecte

11Automatic two-sided copying from the automatic documentfeederA duplex module must be installed for automatic 1-sided to 2-sided or 2-sided to 2-side

12Copying from the document glassWhen copying originals which cannot be fed from the automatic document feeder such as thick originals, open thedocume

134Select the desired output mode (see below).2-SIDED COPYOUTPUTWhen a document isdetected on the documentglass, the group mode willbe automatically s

14Automatic two-sided copying from the document glassA duplex module must be installed for automatic 1-sided to 2-sided or 2-sided to 2-sided copying.

15EXPOSURE ADJUSTMENTSSelect the exposure mode to be consistent with the type of originals to be copied. The selections are AUTO, TEXT,TEXT/PHOTO and

16REDUCTION/ENLARGEMENT/ZOOMReduction and enlargement ratios can be selected either automatically or manually as described in this section.●Automatic

17Manual selection1Place the original in the document feeder trayor on the document glass. (page 7)NOTEWhen the document feeder is being used, the ava

cover1.p65 2/04/01, 19:172

18SPECIAL PAPERSIf a bypass tray and a duplex module, a duplex module/bypass tray or a multi purpose drawer*1 is installed, specialpapers can be fed.

19SPECIAL MODEWhen the [SPECIAL MODES] key on the basic screen of the copy mode is touched, the special modes screencontaining six special function to

20Margin shiftThe margin shift function will automatically shift the text or image on the copy paper approximately 1/2" (10 mm) in itsinitial set

21EraseThe erase function is used to erase the shadow lines on copies produced when copying thick originals or books. Theerase modes that can be selec

22Dual page copyThe dual page copy function produces separate copies of two documents placed side by side on the document glass.It is especially usefu

23Pamphlet copyThe pamphlet copy function is used to arrange copies in proper order for eventual center-stapling and folding into abooklet. Two origin

24Job buildThe number of originals that can be copied into a set of copies in a single run is limited by the capacity of the memoryavailable*1 for sca

25Multi shotThe multi shot function is used to copy up to four originals, collectively in a specified order, per sheet of copy paper inany one of four

26JOB PROGRAM MEMORYFrequently used job programs can be stored in each of ten storage registers. This is convenient for quick job recallwithout losing

27Recalling a job programDeleting a stored job programJOB PROGRAM MEMORY1Press the [#/P] key.2Touch the desired storage register number keyto recall t

1INTRODUCTIONThis manual describes only copier features. For operation procedures relating to both the basic printer and copierfeatures, refer to the

28INTERRUPTING A PRINT OR COPY RUNINTERRUPT can be used to temporarily stop a long print or copy job so that another copy job can be run. Only copyjob

29MISFEED REMOVALMisfeed in scanner moduleWhen an original has misfed in the scanner module, remove the misfed original following the procedure below.

30TROUBLESHOOTINGWhenever the machine stops or operation is not possible, check the operation panel display for messages. In mostcases, these messages

31SPECIFICATIONSCopierResolution Scan: 600 dpi or 300 dpi, output: 600 dpiGradation Scan: 256 levels, output: 2 levelsOriginals Sheets, bound document

32KEY OPERATOR PROGRAMSThis section describes all key operator programs relating only to the copier and facsimile functions. For the keyoperator progr

33Setting programsThis section describes the setting of programs commonto copier, facsimile and network scanning features. Forprograms dedicated to fa

34Device controlOriginal size detection and disabling of the documentfeeder can be set.Original size detector settingThis program is used to select th

cover4.p65 2/04/01, 19:181

2001D KS1TINSE2077FCZZOperation manual for copierPRINTED IN CHINASHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey 07430-2135.SHA

2CONTENTSPageINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1CONTENTS . . . . . . . . . . . . . . . . .

3PART NAMES AND FUNCTIONS(B/W scanner module/DSPF)ExteriorDSPF exit areaScanned originals are deposited here.Document feeding area cover (page 29)Open

4Touch panel (next page)The machine status, messages and touch keys aredisplayed on the panel. When the machine is in thestandby state, the display wi

5Touch Panel (basic screen of copy mode)When the copy mode key is pressed, this display screen will appear showing the basic copy mode selections.(For

6AUTOMATIC DOCUMENT FEEDEROriginals set in the automatic document feeder will be automatically fed and copied sequentially.The automatic document feed

7SETTING ORIGINALS When using the document glassOpen the document cover, place an original facedown on the document glass, and then gentlyclose t