Sharp MX-M550N Uživatelský manuál stáhnout pdf (Strana 15)

GENERAL SETTINGS

IPv6 setting

When using this product in a network that uses the

TCP/IP protocol (IPv6), use this setting to set the IP

address (enable IPv6, DHCPv6, IP address, prefix

length, and default gateway) of this product. By factory

default, the IPv6 setting is disabled. When using this

product on a TCP/IP network, be sure to turn on the

"Enable TCP/IP" setting below.

In an IPv6 environment, the machine can use LPD or

IPP protocol.

Enable TCP/IP

When using this product in a network that uses the

TCP/IP protocol, set this setting. Also set the IP

address using the setting "IP address setting" above.

Default setting: Enable

Enable NetWare

When using this product in a network that uses the

NetWare protocol, set this setting.

Default setting: Enable

Enable EtherTalk

When using this product in a network that uses the

EtherTalk protocol, set this setting.

Default setting: Enable

Enable NetBEUI

When using this product in a network that uses the

EtherTalk protocol, set this setting.

Default setting: Enable

Reset the NIC

This setting is used to reset all setting items of NIC

(Network Interface Card) of this product to the factory

default settings.

Tandem setting

This setting is used to configure the IP address and

port number of the client printer when you wish to have

two machines (which are used as TCP/IP network

printers) print in tandem.

The factory default setting for the port number is

[50001]. Unless you experience difficulty with this

setting, it does not need to be changed.

The tandem function can also be prohibited, or the

reception of tandem data from the other machine can

be prohibited. (Normally this is not necessary.)

To prohibit the tandem function, select "DISABLING

OF MASTER MACHINE MODE".

To prohibit reception of tandem data from the other

machine, select "DISABLING OF SLAVE MACHINE

MODE".

PING command

This setting is used to check if the machine and a

computer connected to the network can communicate.

Enter the IP address of the computer that you wish to

check and touch the [START] key. A message will

appear indicating whether or not there was a response

from the computer.

Security settings

The following settings are related to security. Touch the

[SECURITY SETTINGS] key to configure the settings.

When any of these settings are changed, you must exit

the administrator settings, turn off the main switch, wait

a brief interval, and then turn the main switch back on

to make the new settings take effect.

SSL setting

SSL can be used for data transmission over a network.

SSL is a protocol that enables the encryption of

information communicated over a network. Encrypting

data makes it possible to transmit and receive sensitive

information safely.

Server port

● HTTPS: Apply SSL encryption to HTTP

communication.

● IPP-SSL: Apply SSL encryption to IPP

communication.

Client port

● FTPS: Apply SSL encryption to FTP

communication.

● SMTP-SSL: Apply SSL encryption to SMTP

communication.

● POP3-SSL: Apply SSL encryption to POP3

communication.

Level of encryption

The encryption strength can be set to one of 3 levels.

If DHCP is used, the IP address assigned to the

machine may be changed automatically on occasion.

If this happens, printing will not be possible.

NOTE

If any of the [NETWORK SETTINGS] were changed

prior to execution of this setting, you must turn off the

power switch after exiting the administrator setting,

wait briefly, and then turn on the power switch to

make the factory default settings take effect.

NOTE

To use the tandem function when auditing mode is

enabled, the same account number must be entered

on both machines. If the same account number is not

entered, only the server machine may print or the

printed pages may not be added to the correct account.

DragonII_Admin_sec.fm 13 ページ２００７年４月９日　月曜日　午後３時３０分

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 27 28

Komentáře k této Příručce

Žádné komentáře

Sharp MX-M550N Uživatelský manuál Strana 15

Komentáře k této Příručce

Související produkty a manuály pro Sporáky Sharp MX-M550N