Sharp JW-21MN Uživatelský manuál

Version 1.1Produced in May 2002LCD Control TerminalUser's Manual (Ladder Monitor Version)ZM-42/43/52/72/82Thank you for purchasing our LCD contr

6-1Chapter 6: Ladder Monitor Display6-1 Outline of ladder monitor display- On a normal display screen, put on an overlap screen. The LCD control termi

6-26-4 How to set ladder monitorStart up the ZM-71SE software and set according to the setting procedures below.Copy screen data of the basic screen d

6-3[3] Copy macro block (No. 0 to 13)If some macro blocks are already used, change numbers in order not to double the same macro blocknumbers.Especial

6-4 When the symbol/comment is saved in ZM70 format, a "*.mg" file is created by dividing files so eachhas 256 symbols/comments at maximum.[

6-5[5] Setting screen for display ladder chart(1) Initial setting in order to use the ladder monitor (Select from edit items).Select "System sett

6-6 When "Call" is selected, the "Overlap (Call)" setting dialog opens. Set as shown below.Overlap No.: 0 (Enter No. 0 that was as

6-7 When "Multi" is selected, the "Overlap (Multi)" setting dialog opens. Set as shown below.Overlap No.: 1 (Enter No. 1 the same

6-8(4) Set a switch that is used to display a ladder chart on the screen.Arrange switches on the screen, and set the following in the switch dialog.Th

6-9 Click the "Use ON Macro" to enable this function on the "Detail" setting menu. Enter "CALL 0" in the "ON Macro

6-10(5) Set a switch in order to display numeric keys that are used to enter the coil number on the screen.This paragraph describes an example of sett

Table of ContentsBefore useChapter 1: Outline ... 1

6-11(6) Set a switch that is used to search and display a ladder chart linking with the relay mode.Arrange a switch on the screen and set the followin

6-12 Click "Use ON Macro" to make effective this function on the "Detail" setting menu. For "ON Macro Edit," enter the m

6-13[6] System update in order to support the ladder monitor screen data function.In order to display the ladder monitor, the "main program"

6-14 Ladder monitor supporting version* If the extension program information switch is not displayed, the system may not be properly updated.Try updat

6-156-5 Description of ladder monitor screen data6-5-1 Display area for ladder chart displaySpecify [Display Area] inside the multi overlap with the f

6-16[2] How to set macro for ladder circuit displayThere are four types of parameters to specify searching memory No. for displaying ladder circuit.In

6-17 Description of multi overlap No. 0 (call overlap) screenFor displaying ladder circuit, switches are arranged on a matrix of 15 (horizontal) x 12

6-18(3) Scroll instruction and search instructionOn the basic screen "LADDER82.Z71," these instructions use macro blocks Nos. 2 to 5, and No

6-19- SET-LDR: FIND+Setting display of macro block No. 8 (search in positive direction: Executes the call with CALL 8)- SET-LDR: F-RETURNSetting displ

6-20 Description of ladder monitor control switches (operate after displaying ladder circuit)Function of ladder control switches that are arranged on

Before use [1] Differences from the ZM-70T's ladder monitor function Can use a 32-pixel per character font (smooth 4x character font).However, th

6-21(4) Numeric key memory search instruction- SET-LDR: COIL-FIND Setting display of macro block No. 6 (Numeric key input search: Executes call by CAL

6-22 Numeric key screen setting screen of multi overlap No. 1- Description of ON macro edit of the "Search" screenPress the "Search&quo

6-23 Display open macro setting of multi overlap No. 1When the multi overlap is opened, the LCD control terminal turns ON the numeric key memory $u070

6-24(6) Relay mode link search instructionThe software can link ladder monitor display by directly searching a coil which is turning ON the errormessa

6-25 Setting relay mode memory (set the memory on the dialog below to 10000)If the relay mode memory was changed, set the 9th line of the switch ON ma

6-266-6 Description of details displayed on screen when displaying laddermonitor(1) Upper zone of the display area is for displaying ladder program.Wh

1-1Chapter 1: OutlineThe ZM-42/43/52/72/82 series LCD control terminal can display a ladder circuit for a PC (programmable con-troller) used for facil

2-1Chapter 2: Precautions for use(1) Installation location and environmentDo not install the LCD control terminal in any of the following locations.-

3-1Chapter 3: System Configuration*1: Prepare this connection cable separately. A D-sub 25P connector (male) is used forconnecting to the display term

4-1Chapter 4: Connecting to a PC[1] Compatible PCs- Only version 5.8 or later of the JW-20CM can be used for a multi-link connection. Use MODE "4

4-2 Connection to the PG port (support tool connection connector) on a JW-32CUH/H1, JW-33CUH/H1/H2/H3, JW-21CU/22CU, JW-22CM, or JW-21MN.(2) RS-422 (n

5-1Chapter 5: Ladder Monitor Specifications*1: Cannot display more than two networks at the same time.*2: When the ZM-42/43 series is used, the screen